Single Layer Printed Reflectarrays at MM-Waves

J. Lanteri; J. Y. Dauvignac; Ch. Pichot; C. Migliaccio

doi:doi:10.11648/j.jeee.20130101.12

| Peer-Reviewed

Single Layer Printed Reflectarrays at MM-Waves

J. Lanteri, J. Y. Dauvignac, Ch. Pichot, C. Migliaccio

Published in Journal of Electrical and Electronic Engineering (Volume 1, Issue 1)

Published: 2 April 2013

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

This paper talks about a method of conception and design constraints on mm-wave reflectarrays. The developed tool allows us to plan quickly the behavior of large reflectarray (several tens of wavelength) according to parameters as illumination law or manufacturing tolerance with good agreement with measurements. An ultra-low side-lobe reflectarrays of 130 mm diameter is designed. The structure combines the advantages of a reflectarray with an offset source and those of a specific primary source, exhibiting a prolate radiation pattern, having very low side lobe levels. The maximum gain obtained at 94 GHz is 40 dBi and the side-lobe level is inferior to -28 dB. Finally, a simultaneous multi-lobe antenna is designed at 94 GHz. The primary source is an open-ended waveguide and the phase profile is calculated by the program introduced in the first part. In this case, the four main lobes are placed in the same plane and for equal to -30, -10, 10, 30°. This reflectarray can be used for actual and future generations of automotive radar. The first obtained results are encouraging and show the validity of the concept. Solution retained here is a low-cost solution. The proposed structures are developed on a single layer substrate and fabricated using standard photolithographic techniques. The aim of this article is to show that we can obtain interesting results with relatively simple and low-cost solutions, but also to show the limits of these type of solutions.

Published in	Journal of Electrical and Electronic Engineering (Volume 1, Issue 1)
DOI	10.11648/j.jeee.20130101.12
Page(s)	20-28
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2013. Published by Science Publishing Group

Keywords

Reflectarray, Reflector Antenna, Reflector Antenna Feed, Mm-Wave Arrays Antenna

References

[1]	D. M. Pozar, S. D. Targonski, and H. D. Syrigos, "Design of millimeter wave microstrip reflectarrays", IEEE Trans. Antennas Propag., vol. 45, pp. 287-296, February 1997.
[2]	W. Menzel, D. Pilz, R. Leberer, "A 77 GHz FM/CW radar front-end with a low profile lowloss printed antenna", IEEE Trans. Microwave Theory and Techniques, vol.47, pp.2237-2241, December 1999.
[3]	S. Dieter, C. Fisher, W. Menzel, "Design of a Folded Reflectarray Antenna Using Particle Swarm Optimization", 40th European Microwave Conference, September 28 - 30, 2010, Paris, France
[4]	N. Yonemoto, N. Yamamoto, K. Yamada, H. Yasui, N. Tanaka, C. Migliaccio, J-Y. Dauvignac, Ch. Pichot, " Performance of obstacle detection and collision warning system for civil helicopters" , Defense and Security Symposium 2006, SPIE, AeroSense, 17-21-April 2006, Orlando, Florida, USA
[5]	W. Menzel, D. Pilz, M. Al-Tikriti, "Millimeter wave folded reflector antennas with high gain, low loss and low profile", IEEE Antenna's and Propagation Magazine,vol.44, pp.24-29, june 2002
[6]	J.A. Encinar, "Design of two layer printed reflectarrays using patches of variable size", IEEE Trans. Antennas Propagat., vol.49, pp.1403-1410, october 2001
[7]	N. Misran, R. Cahill, and V. F. Fusco, "Design optimisation of ring elements for broadband reﬂectarray antenna," Proc. Inst. Elect. Eng.- Microw. Antennas Propag., vol. 150, no. 6, pp. 440–444, Dec. 2003.
[8]	A. Yu, F. Yang, A.Z. Elsherbeni, J. Huang, "A single layer broadband circularly polarized reflectarray based on the element rotation technique", Antennas and Propagation Society International Symposium, 2009. APSURSI '09. IEEE
[9]	W. Menzel, J. Li, S. Dieter, "Folded reflectarray antenna based on a single layer reflector with increased phase angle range", 3rd European Conference on Antennas and Propagation,(EuCAP 2009), 23-27 March 2009
[10]	L. Matekovits, V.A. Laza, F. Vipiana, P. Pirinoli, G. Vecchi, " Multiscale analysis of array and antenna farm problems", IEEE APS Symposium, 2005
[11]	Scilab www.scilab.org
[12]	O. Bucci, G. Mazzarella, G. Panariello, "Reconfigurable arrays by phase-only control", IEEE Trans. Antennas Propagat, Vol. 39, pp. 919-925, July 1991.
[13]	C. Han, C. Rodenbeck, J. Huang, K. Chang, "A C/Ka Dual Frequency Dual Layer Circularly Polarized Reflect array Antenna with MicrosItrip Rings Elements", IEEE Trans. Antennas Propagat, Vol. 52, No. 11, pp. 2871-2876, November 2004.
[14]	A. Zeitler, J. Lanteri, Ch. Pichot, C. Migliaccio, P. Feil, and W. Menzel, "Folded Reflectarrays with Shaped Beam Pattern for Foreign Object Debris Detection on Runways", IEEE Trans. Antennas Propagat. Vol.58 n°8, pp. 3065-3068, 2010.R.
[15]	D.Slepian and H.O Pollak, "Prolate Spheroidal wave functions, Fourier analysis and uncertainty I", Bell System Technical Journal, vol. 40, pp. 43-64, January 1961.
[16]	H.J. Landau and H.O. Pollak. Prolate spheroidal wave functions,Fourier analysis and uncertainty, II. Bell System Technical Journal, 40:65-84, January 1961.
[17]	R. Soummer et al., "Prolate apodized coronography: numerical simulations for circular apertures", Astronomy with High Contrast Imaging, C. Aime and R. Soummer (eds), EAS Publications Series (8) (2003), pp. 93-105.
[18]	A. Berthon and R. P. Bills, "Integral equation analysis of radiating structures of revolution", IEEE Trans. Antennas Propagat, Vol. 37, pp. 159-170, February 1989.
[19]	J.Lanteri et al., "Improvement of reflectarrays and lenses radiation pattern by prolate spheroidal functions in W band", EUCAP, November 2006, Nice, France.

Cite This Article

Plain Text BibTeX RIS

APA Style

J. Lanteri, J. Y. Dauvignac, Ch. Pichot, C. Migliaccio. (2013). Single Layer Printed Reflectarrays at MM-Waves. Journal of Electrical and Electronic Engineering, 1(1), 20-28. https://doi.org/10.11648/j.jeee.20130101.12

Copy | Download

ACS Style

J. Lanteri; J. Y. Dauvignac; Ch. Pichot; C. Migliaccio. Single Layer Printed Reflectarrays at MM-Waves. J. Electr. Electron. Eng. 2013, 1(1), 20-28. doi: 10.11648/j.jeee.20130101.12

Copy | Download

AMA Style

J. Lanteri, J. Y. Dauvignac, Ch. Pichot, C. Migliaccio. Single Layer Printed Reflectarrays at MM-Waves. J Electr Electron Eng. 2013;1(1):20-28. doi: 10.11648/j.jeee.20130101.12

Copy | Download

@article{10.11648/j.jeee.20130101.12,
  author = {J. Lanteri and J. Y. Dauvignac and Ch. Pichot and C. Migliaccio},
  title = {Single Layer Printed Reflectarrays at MM-Waves},
  journal = {Journal of Electrical and Electronic Engineering},
  volume = {1},
  number = {1},
  pages = {20-28},
  doi = {10.11648/j.jeee.20130101.12},
  url = {https://doi.org/10.11648/j.jeee.20130101.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20130101.12},
  abstract = {This paper talks about a method of conception and design constraints on mm-wave reflectarrays. The developed tool allows us to plan quickly the behavior of large reflectarray (several tens of wavelength) according to parameters as illumination law or manufacturing tolerance with good agreement with measurements. An ultra-low side-lobe reflectarrays of 130 mm diameter is designed. The structure combines the advantages of a reflectarray with an offset source and those of a specific primary source, exhibiting a prolate radiation pattern, having very low side lobe levels. The maximum gain obtained at 94 GHz is 40 dBi and the side-lobe level is inferior to -28 dB. Finally, a simultaneous multi-lobe antenna is designed at 94 GHz. The primary source is an open-ended waveguide and the phase profile is calculated by the program introduced in the first part. In this case, the four main lobes are placed in the same plane and for equal to -30, -10, 10, 30°. This reflectarray can be used for actual and future generations of automotive radar. The first obtained results are encouraging and show the validity of the concept. Solution retained here is a low-cost solution. The proposed structures are developed on a single layer substrate and fabricated using standard photolithographic techniques. The aim of this article is to show that we can obtain interesting results with relatively simple and low-cost solutions, but also to show the limits of these type of solutions.},
 year = {2013}
}

Copy | Download

TY - JOUR
T1 - Single Layer Printed Reflectarrays at MM-Waves
AU - J. Lanteri
AU - J. Y. Dauvignac
AU - Ch. Pichot
AU - C. Migliaccio
Y1 - 2013/04/02
PY - 2013
N1 - https://doi.org/10.11648/j.jeee.20130101.12
DO - 10.11648/j.jeee.20130101.12
T2 - Journal of Electrical and Electronic Engineering
JF - Journal of Electrical and Electronic Engineering
JO - Journal of Electrical and Electronic Engineering
SP - 20
EP - 28
PB - Science Publishing Group
SN - 2329-1605
UR - https://doi.org/10.11648/j.jeee.20130101.12
AB - This paper talks about a method of conception and design constraints on mm-wave reflectarrays. The developed tool allows us to plan quickly the behavior of large reflectarray (several tens of wavelength) according to parameters as illumination law or manufacturing tolerance with good agreement with measurements. An ultra-low side-lobe reflectarrays of 130 mm diameter is designed. The structure combines the advantages of a reflectarray with an offset source and those of a specific primary source, exhibiting a prolate radiation pattern, having very low side lobe levels. The maximum gain obtained at 94 GHz is 40 dBi and the side-lobe level is inferior to -28 dB. Finally, a simultaneous multi-lobe antenna is designed at 94 GHz. The primary source is an open-ended waveguide and the phase profile is calculated by the program introduced in the first part. In this case, the four main lobes are placed in the same plane and for equal to -30, -10, 10, 30°. This reflectarray can be used for actual and future generations of automotive radar. The first obtained results are encouraging and show the validity of the concept. Solution retained here is a low-cost solution. The proposed structures are developed on a single layer substrate and fabricated using standard photolithographic techniques. The aim of this article is to show that we can obtain interesting results with relatively simple and low-cost solutions, but also to show the limits of these type of solutions.
VL - 1
IS - 1
ER -

Copy | Download

Author Information

J. Lanteri

Laboratory of Electronics, Antennas and Telecommunications (LEAT), University of Nice-Sophia Antipolis, CNRS, Sophia-Antipolis, France
J. Y. Dauvignac

Laboratory of Electronics, Antennas and Telecommunications (LEAT), University of Nice-Sophia Antipolis, CNRS, Sophia-Antipolis, France
Ch. Pichot

Laboratory of Electronics, Antennas and Telecommunications (LEAT), University of Nice-Sophia Antipolis, CNRS, Sophia-Antipolis, France
C. Migliaccio

Laboratory of Electronics, Antennas and Telecommunications (LEAT), University of Nice-Sophia Antipolis, CNRS, Sophia-Antipolis, France

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

J. Lanteri, J. Y. Dauvignac, Ch. Pichot, C. Migliaccio. (2013). Single Layer Printed Reflectarrays at MM-Waves. Journal of Electrical and Electronic Engineering, 1(1), 20-28. https://doi.org/10.11648/j.jeee.20130101.12

Copy | Download

ACS Style

J. Lanteri; J. Y. Dauvignac; Ch. Pichot; C. Migliaccio. Single Layer Printed Reflectarrays at MM-Waves. J. Electr. Electron. Eng. 2013, 1(1), 20-28. doi: 10.11648/j.jeee.20130101.12

Copy | Download

AMA Style

J. Lanteri, J. Y. Dauvignac, Ch. Pichot, C. Migliaccio. Single Layer Printed Reflectarrays at MM-Waves. J Electr Electron Eng. 2013;1(1):20-28. doi: 10.11648/j.jeee.20130101.12

Copy | Download

@article{10.11648/j.jeee.20130101.12,
  author = {J. Lanteri and J. Y. Dauvignac and Ch. Pichot and C. Migliaccio},
  title = {Single Layer Printed Reflectarrays at MM-Waves},
  journal = {Journal of Electrical and Electronic Engineering},
  volume = {1},
  number = {1},
  pages = {20-28},
  doi = {10.11648/j.jeee.20130101.12},
  url = {https://doi.org/10.11648/j.jeee.20130101.12},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20130101.12},
  abstract = {This paper talks about a method of conception and design constraints on mm-wave reflectarrays. The developed tool allows us to plan quickly the behavior of large reflectarray (several tens of wavelength) according to parameters as illumination law or manufacturing tolerance with good agreement with measurements. An ultra-low side-lobe reflectarrays of 130 mm diameter is designed. The structure combines the advantages of a reflectarray with an offset source and those of a specific primary source, exhibiting a prolate radiation pattern, having very low side lobe levels. The maximum gain obtained at 94 GHz is 40 dBi and the side-lobe level is inferior to -28 dB. Finally, a simultaneous multi-lobe antenna is designed at 94 GHz. The primary source is an open-ended waveguide and the phase profile is calculated by the program introduced in the first part. In this case, the four main lobes are placed in the same plane and for equal to -30, -10, 10, 30°. This reflectarray can be used for actual and future generations of automotive radar. The first obtained results are encouraging and show the validity of the concept. Solution retained here is a low-cost solution. The proposed structures are developed on a single layer substrate and fabricated using standard photolithographic techniques. The aim of this article is to show that we can obtain interesting results with relatively simple and low-cost solutions, but also to show the limits of these type of solutions.},
 year = {2013}
}

Copy | Download